Product Description
SPROCKET 1/2” X 5/16” 08B SERIES SPROCKETS
| For Chain Acc.to DIN8187 ISO/R 606 | |||||
| Tooth Radius r3 | 13.0mm | ||||
| Radius Width C | 1.3mm | ||||
| Tooth Width b1 | 7.0mm | ||||
| Tooth Width B1 | 7.2mm | ||||
| Tooth Width B2 | 21.0mm | ||||
| Tooth Width B3 | 34.9mm | ||||
| 08B SERIES ROLLER CHAINS | |||||
| Pitch | 12.7 mm | ||||
| Internal Width | 7.75 mm | ||||
| Roller Diameter | 8.51 mm | ||||
| Z | de | dp | SIMPLEX | DUPLEX | TRIPLEX |
| D1 | D2 | D3 | |||
| 8 | 37.2 | 33.18 | 8 | 10 | 10 |
| 9 | 41.0 | 37.13 | 8 | 10 | 10 |
| 10 | 45.2 | 41.10 | 8 | 10 | 10 |
| 11 | 48.7 | 45.07 | 10 | 10 | 12 |
| 12 | 53.0 | 49.07 | 10 | 10 | 12 |
| 13 | 57.4 | 53.06 | 10 | 10 | 12 |
| 14 | 61.8 | 57.07 | 10 | 10 | 12 |
| 15 | 65.5 | 61.09 | 10 | 10 | 12 |
| 16 | 69.5 | 65.10 | 10 | 12 | 16 |
| 17 | 73.6 | 69.11 | 10 | 12 | 16 |
| 18 | 77.8 | 73.14 | 10 | 12 | 16 |
| 19 | 81.7 | 77.16 | 10 | 12 | 16 |
| 20 | 85.8 | 81.19 | 10 | 12 | 16 |
| 21 | 89.7 | 85.22 | 12 | 16 | 16 |
| 22 | 93.8 | 89.24 | 12 | 16 | 16 |
| 23 | 98.2 | 93.27 | 12 | 16 | 16 |
| 24 | 101.8 | 97.29 | 12 | 16 | 16 |
| 25 | 105.8 | 101.33 | 12 | 16 | 16 |
| 26 | 110.0 | 105.36 | 16 | 16 | 16 |
| 27 | 114.0 | 109.40 | 16 | 16 | 16 |
| 28 | 118.0 | 113.42 | 16 | 16 | 16 |
| 29 | 122.0 | 117.46 | 16 | 16 | 16 |
| 30 | 126.1 | 121.50 | 16 | 16 | 16 |
| 31 | 130.2 | 125.54 | 16 | 16 | 20 |
| 32 | 134.3 | 129.56 | 16 | 16 | 20 |
| 33 | 138.4 | 133.60 | 16 | 16 | 20 |
| 34 | 142.6 | 137.64 | 16 | 16 | 20 |
| 35 | 146.7 | 141.68 | 16 | 16 | 20 |
| 36 | 151.0 | 145.72 | 16 | 20 | 20 |
| 37 | 154.6 | 149.76 | 16 | 20 | 20 |
| 38 | 158.6 | 153.80 | 16 | 20 | 20 |
| 39 | 162.7 | 157.83 | 16 | 20 | 20 |
| 40 | 166.8 | 161.87 | 16 | 20 | 20 |
| 41 | 171.4 | 165.91 | 20 | 20 | 25 |
| 42 | 175.4 | 169.94 | 20 | 20 | 25 |
| 43 | 179.7 | 173.98 | 20 | 20 | 25 |
| 44 | 183.8 | 178.02 | 20 | 20 | 25 |
| 45 | 188.0 | 182.07 | 20 | 20 | 25 |
| 46 | 192.1 | 186.10 | 20 | 20 | 25 |
| 47 | 196.2 | 190.14 | 20 | 20 | 25 |
| 48 | 200.3 | 194.18 | 20 | 20 | 25 |
| 49 | 204.3 | 198.22 | 20 | 20 | 25 |
| 50 | 208.3 | 202.26 | 20 | 20 | 25 |
| 51 | 212.1 | 206.30 | 20 | 25 | 25 |
| 52 | 216.1 | 210.34 | 20 | 25 | 25 |
| 53 | 220.2 | 214.37 | 20 | 25 | 25 |
| 54 | 224.1 | 218.43 | 20 | 25 | 25 |
| 55 | 228.1 | 222.46 | 20 | 25 | 25 |
| 56 | 232.2 | 226.50 | 20 | 25 | 25 |
| 57 | 236.4 | 230.54 | 20 | 25 | 25 |
| 58 | 240.5 | 234.58 | 20 | 25 | 25 |
| 59 | 244.5 | 238.62 | 20 | 25 | 25 |
| 60 | 248.6 | 242.66 | 20 | 25 | 25 |
| 62 | 256.9 | 250.74 | 25 | 25 | 25 |
| 64 | 265.1 | 258.82 | 25 | 25 | 25 |
| 65 | 269.0 | 262.86 | 25 | 25 | 25 |
| 66 | 273.0 | 266.91 | 25 | 25 | 25 |
| 68 | 281.0 | 274.99 | 25 | 25 | 25 |
| 70 | 289.0 | 283.07 | 25 | 25 | 25 |
| 72 | 297.2 | 291.15 | 25 | 25 | 25 |
| 75 | 309.2 | 303.28 | 25 | 25 | 25 |
| 76 | 313.2 | 307.32 | 25 | 25 | 25 |
| 78 | 321.4 | 315.40 | 25 | 25 | 25 |
| 80 | 329.4 | 323.49 | 25 | 25 | 25 |
| 85 | 349.0 | 343.69 | 25 | 25 | 25 |
| 90 | 369.9 | 363.90 | 25 | 25 | 25 |
| 95 | 390.1 | 384.11 | 25 | 25 | 25 |
| 100 | 410.3 | 404.32 | 25 | 25 | 25 |
| 110 | 450.7 | 444.74 | 25 | 25 | 25 |
| 114 | 466.9 | 460.91 | 25 | 25 | 25 |
| 120 | 491.2 | 485.16 | 25 | 25 | 25 |
| 125 | 511.3 | 505.37 | 25 | 25 | 25 |
BASIC INFO.
|
Type: |
Simplex, Duplex, Triplex |
|
Sprocket Model: |
3/8″,1/2″,5/8″,3/4″,1″,1.25″,1.50″,1.75″,2.00″,2.25″,2.00″,2.25″,2.50″, 3″ |
|
Teeth Number: |
9-100 |
|
Standard: |
ANSI , JIS, DIN, ISO |
|
Material: |
1571, 1045, SS304 , SS316; As Per User Request. |
|
Performance Treatment: |
Carburizing, High Frequency Treatment, Hardening and Tempering, Nitriding |
|
Surface Treatment: |
Black of Oxidation, Zincing, Nickelage. |
| Characteristic | Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc |
| Design criterion | ISO DIN ANSI & Customer Drawings |
| Application | Industrial transmission equipment |
| Package | Wooden Case / Container and pallet, or made-to-order |
|
Certification: |
ISO9001 SGS |
|
Quality Inspection: |
Self-check and Final-check |
|
Sample: |
ODM&OEM, Trial Order Available and Welcome |
| Advantage | Quality first, Service first, Competitive price, Fast delivery |
| Delivery Time | 10 days for samples. 15 days for official order. |
INSTALLATION AND USING
The chain spocket, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.
NOTICE
When fitting new chainwheels it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.
It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.
During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
FOR CHAIN STHangZhouRDS
Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.
ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25
| ASME/ANSI B29.1-2011 Roller Chain Standard Sizes | ||||
| Size | Pitch | Maximum Roller Diameter | Minimum Ultimate Tensile Strength | Measuring Load |
|---|---|---|---|---|
| 25 | 0.250 in (6.35 mm) | 0.130 in (3.30 mm) | 780 lb (350 kg) | 18 lb (8.2 kg) |
| 35 | 0.375 in (9.53 mm) | 0.200 in (5.08 mm) | 1,760 lb (800 kg) | 18 lb (8.2 kg) |
| 41 | 0.500 in (12.70 mm) | 0.306 in (7.77 mm) | 1,500 lb (680 kg) | 18 lb (8.2 kg) |
| 40 | 0.500 in (12.70 mm) | 0.312 in (7.92 mm) | 3,125 lb (1,417 kg) | 31 lb (14 kg) |
| 50 | 0.625 in (15.88 mm) | 0.400 in (10.16 mm) | 4,880 lb (2,210 kg) | 49 lb (22 kg) |
| 60 | 0.750 in (19.05 mm) | 0.469 in (11.91 mm) | 7,030 lb (3,190 kg) | 70 lb (32 kg) |
| 80 | 1.000 in (25.40 mm) | 0.625 in (15.88 mm) | 12,500 lb (5,700 kg) | 125 lb (57 kg) |
| 100 | 1.250 in (31.75 mm) | 0.750 in (19.05 mm) | 19,531 lb (8,859 kg) | 195 lb (88 kg) |
| 120 | 1.500 in (38.10 mm) | 0.875 in (22.23 mm) | 28,125 lb (12,757 kg) | 281 lb (127 kg) |
| 140 | 1.750 in (44.45 mm) | 1.000 in (25.40 mm) | 38,280 lb (17,360 kg) | 383 lb (174 kg) |
| 160 | 2.000 in (50.80 mm) | 1.125 in (28.58 mm) | 50,000 lb (23,000 kg) | 500 lb (230 kg) |
| 180 | 2.250 in (57.15 mm) | 1.460 in (37.08 mm) | 63,280 lb (28,700 kg) | 633 lb (287 kg) |
| 200 | 2.500 in (63.50 mm) | 1.562 in (39.67 mm) | 78,175 lb (35,460 kg) | 781 lb (354 kg) |
| 240 | 3.000 in (76.20 mm) | 1.875 in (47.63 mm) | 112,500 lb (51,000 kg) | 1,000 lb (450 kg |
For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):
| Pitch (inches) | Pitch expressed in eighths |
ANSI standard chain number |
Width (inches) |
|---|---|---|---|
| 1⁄4 | 2⁄8 | 25 | 1⁄8 |
| 3⁄8 | 3⁄8 | 35 | 3⁄16 |
| 1⁄2 | 4⁄8 | 41 | 1⁄4 |
| 1⁄2 | 4⁄8 | 40 | 5⁄16 |
| 5⁄8 | 5⁄8 | 50 | 3⁄8 |
| 3⁄4 | 6⁄8 | 60 | 1⁄2 |
| 1 | 8⁄8 | 80 | 5⁄8 |
Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.
Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.
Roller chains made using ISO standard are sometimes called as isochains.
WHY CHOOSE US
1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System
The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.
We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.
| Standard Or Nonstandard: | Standard |
|---|---|
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Mining Machinery, Sugar Machinery |
| Hardness: | Hardened Tooth Surface |
| Manufacturing Method: | Cut Gear |
| Toothed Portion Shape: | Spur Gear |
| Material: | Alloy |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
| Customized Request |
|---|
The Difference Between Planetary Gears and Spur Gears
A spur gear is a type of mechanical drive that turns an external shaft. The angular velocity is proportional to the rpm and can be easily calculated from the gear ratio. However, to properly calculate angular velocity, it is necessary to know the number of teeth. Fortunately, there are several different types of spur gears. Here’s an overview of their main features. This article also discusses planetary gears, which are smaller, more robust, and more power-dense.
Planetary gears are a type of spur gear
One of the most significant differences between planetary gears and spurgears is the way that the two share the load. Planetary gears are much more efficient than spurgears, enabling high torque transfer in a small space. This is because planetary gears have multiple teeth instead of just one. They are also suitable for intermittent and constant operation. This article will cover some of the main benefits of planetary gears and their differences from spurgears.
While spur gears are more simple than planetary gears, they do have some key differences. In addition to being more basic, they do not require any special cuts or angles. Moreover, the tooth shape of spur gears is much more complex than those of planetary gears. The design determines where the teeth make contact and how much power is available. However, a planetary gear system will be more efficient if the teeth are lubricated internally.
In a planetary gear, there are three shafts: a sun gear, a planet carrier, and an external ring gear. A planetary gear is designed to allow the motion of one shaft to be arrested, while the other two work simultaneously. In addition to two-shaft operation, planetary gears can also be used in three-shaft operations, which are called temporary three-shaft operations. Temporary three-shaft operations are possible through frictional coupling.
Among the many benefits of planetary gears is their adaptability. As the load is shared between several planet gears, it is easier to switch gear ratios, so you do not need to purchase a new gearbox for every new application. Another major benefit of planetary gears is that they are highly resistant to high shock loads and demanding conditions. This means that they are used in many industries.
They are more robust
An epicyclic gear train is a type of transmission that uses concentric axes for input and output. This type of transmission is often used in vehicles with automatic transmissions, such as a Lamborghini Gallardo. It is also used in hybrid cars. These types of transmissions are also more robust than conventional planetary gears. However, they require more assembly time than a conventional parallel shaft gear.
An epicyclic gearing system has three basic components: an input, an output, and a carrier. The number of teeth in each gear determines the ratio of input rotation to output rotation. In some cases, an epicyclic gear system can be made with two planets. A third planet, known as the carrier, meshes with the second planet and the sun gear to provide reversibility. A ring gear is made of several components, and a planetary gear may contain many gears.
An epicyclic gear train can be built so that the planet gear rolls inside the pitch circle of an outer fixed gear ring, or “annular gear.” In such a case, the curve of the planet’s pitch circle is called a hypocycloid. When epicycle gear trains are used in combination with a sun gear, the planetary gear train is made up of both types. The sun gear is usually fixed, while the ring gear is driven.
Planetary gearing, also known as epicyclic gear, is more durable than other types of transmissions. Because planets are evenly distributed around the sun, they have an even distribution of gears. Because they are more robust, they can handle higher torques, reductions, and overhung loads. They are also more energy-dense and robust. In addition, planetary gearing is often able to be converted to various ratios.
They are more power dense
The planet gear and ring gear of a compound planetary transmission are epicyclic stages. One part of the planet gear meshes with the sun gear, while the other part of the gear drives the ring gear. Coast tooth flanks are used only when the gear drive works in reversed load direction. Asymmetry factor optimization equalizes the contact stress safety factors of a planetary gear. The permissible contact stress, sHPd, and the maximum operating contact stress (sHPc) are equalized by asymmetry factor optimization.
In addition, epicyclic gears are generally smaller and require fewer space than helical ones. They are commonly used as differential gears in speed frames and in looms, where they act as a Roper positive let off. They differ in the amount of overdrive and undergearing ratio they possess. The overdrive ratio varies from fifteen percent to forty percent. In contrast, the undergearing ratio ranges from 0.87:1 to 69%.
The TV7-117S turboprop engine gearbox is the first known application of epicyclic gears with asymmetric teeth. This gearbox was developed by the CZPT Corporation for the Ilyushin Il-114 turboprop plane. The TV7-117S’s gearbox arrangement consists of a first planetary-differential stage with three planet gears and a second solar-type coaxial stage with five planet gears. This arrangement gives epicyclic gears the highest power density.
Planetary gearing is more robust and power-dense than other types of gearing. They can withstand higher torques, reductions, and overhung loads. Their unique self-aligning properties also make them highly versatile in rugged applications. It is also more compact and lightweight. In addition to this, epicyclic gears are easier to manufacture than planetary gears. And as a bonus, they are much less expensive.
They are smaller
Epicyclic gears are small mechanical devices that have a central “sun” gear and one or more outer intermediate gears. These gears are held in a carrier or ring gear and have multiple mesh considerations. The system can be sized and speeded by dividing the required ratio by the number of teeth per gear. This process is known as gearing and is used in many types of gearing systems.
Planetary gears are also known as epicyclic gearing. They have input and output shafts that are coaxially arranged. Each planet contains a gear wheel that meshes with the sun gear. These gears are small and easy to manufacture. Another advantage of epicyclic gears is their robust design. They are easily converted into different ratios. They are also highly efficient. In addition, planetary gear trains can be designed to operate in multiple directions.
Another advantage of epicyclic gearing is their reduced size. They are often used for small-scale applications. The lower cost is associated with the reduced manufacturing time. Epicyclic gears should not be made on N/C milling machines. The epicyclic carrier should be cast and tooled on a single-purpose machine, which has several cutters cutting through material. The epicyclic carrier is smaller than the epicyclic gear.
Epicyclic gearing systems consist of three basic components: an input, an output, and a stationary component. The number of teeth in each gear determines the ratio of input rotation to output rotation. Typically, these gear sets are made of three separate pieces: the input gear, the output gear, and the stationary component. Depending on the size of the input and output gear, the ratio between the two components is greater than half.
They have higher gear ratios
The differences between epicyclic gears and regular, non-epicyclic gears are significant for many different applications. In particular, epicyclic gears have higher gear ratios. The reason behind this is that epicyclic gears require multiple mesh considerations. The epicyclic gears are designed to calculate the number of load application cycles per unit time. The sun gear, for example, is +1300 RPM. The planet gear, on the other hand, is +1700 RPM. The ring gear is also +1400 RPM, as determined by the number of teeth in each gear.
Torque is the twisting force of a gear, and the bigger the gear, the higher the torque. However, since the torque is also proportional to the size of the gear, bigger radii result in lower torque. In addition, smaller radii do not move cars faster, so the higher gear ratios do not move at highway speeds. The tradeoff between speed and torque is the gear ratio.
Planetary gears use multiple mechanisms to increase the gear ratio. Those using epicyclic gears have multiple gear sets, including a sun, a ring, and two planets. Moreover, the planetary gears are based on helical, bevel, and spur gears. In general, the higher gear ratios of epicyclic gears are superior to those of planetary gears.
Another example of planetary gears is the compound planet. This gear design has two different-sized gears on either end of a common casting. The large end engages the sun while the smaller end engages the annulus. The compound planets are sometimes necessary to achieve smaller steps in gear ratio. As with any gear, the correct alignment of planet pins is essential for proper operation. If the planets are not aligned properly, it may result in rough running or premature breakdown.
editor by CX 2023-05-19
China wholesaler Gearbox Belt Conveyor Roller Chains Driving Chains Transmission Stainless Steel Chain and Sprocket Kit Oil Industry Gears Bevel Gear worm and wheel gear
Product Description
SPROCKET 1/2” X 5/16” 08B SERIES SPROCKETS
| For Chain Acc.to DIN8187 ISO/R 606 | |||||
| Tooth Radius r3 | 13.0mm | ||||
| Radius Width C | 1.3mm | ||||
| Tooth Width b1 | 7.0mm | ||||
| Tooth Width B1 | 7.2mm | ||||
| Tooth Width B2 | 21.0mm | ||||
| Tooth Width B3 | 34.9mm | ||||
| 08B SERIES ROLLER CHAINS | |||||
| Pitch | 12.7 mm | ||||
| Internal Width | 7.75 mm | ||||
| Roller Diameter | 8.51 mm | ||||
| Z | de | dp | SIMPLEX | DUPLEX | TRIPLEX |
| D1 | D2 | D3 | |||
| 8 | 37.2 | 33.18 | 8 | 10 | 10 |
| 9 | 41.0 | 37.13 | 8 | 10 | 10 |
| 10 | 45.2 | 41.10 | 8 | 10 | 10 |
| 11 | 48.7 | 45.07 | 10 | 10 | 12 |
| 12 | 53.0 | 49.07 | 10 | 10 | 12 |
| 13 | 57.4 | 53.06 | 10 | 10 | 12 |
| 14 | 61.8 | 57.07 | 10 | 10 | 12 |
| 15 | 65.5 | 61.09 | 10 | 10 | 12 |
| 16 | 69.5 | 65.10 | 10 | 12 | 16 |
| 17 | 73.6 | 69.11 | 10 | 12 | 16 |
| 18 | 77.8 | 73.14 | 10 | 12 | 16 |
| 19 | 81.7 | 77.16 | 10 | 12 | 16 |
| 20 | 85.8 | 81.19 | 10 | 12 | 16 |
| 21 | 89.7 | 85.22 | 12 | 16 | 16 |
| 22 | 93.8 | 89.24 | 12 | 16 | 16 |
| 23 | 98.2 | 93.27 | 12 | 16 | 16 |
| 24 | 101.8 | 97.29 | 12 | 16 | 16 |
| 25 | 105.8 | 101.33 | 12 | 16 | 16 |
| 26 | 110.0 | 105.36 | 16 | 16 | 16 |
| 27 | 114.0 | 109.40 | 16 | 16 | 16 |
| 28 | 118.0 | 113.42 | 16 | 16 | 16 |
| 29 | 122.0 | 117.46 | 16 | 16 | 16 |
| 30 | 126.1 | 121.50 | 16 | 16 | 16 |
| 31 | 130.2 | 125.54 | 16 | 16 | 20 |
| 32 | 134.3 | 129.56 | 16 | 16 | 20 |
| 33 | 138.4 | 133.60 | 16 | 16 | 20 |
| 34 | 142.6 | 137.64 | 16 | 16 | 20 |
| 35 | 146.7 | 141.68 | 16 | 16 | 20 |
| 36 | 151.0 | 145.72 | 16 | 20 | 20 |
| 37 | 154.6 | 149.76 | 16 | 20 | 20 |
| 38 | 158.6 | 153.80 | 16 | 20 | 20 |
| 39 | 162.7 | 157.83 | 16 | 20 | 20 |
| 40 | 166.8 | 161.87 | 16 | 20 | 20 |
| 41 | 171.4 | 165.91 | 20 | 20 | 25 |
| 42 | 175.4 | 169.94 | 20 | 20 | 25 |
| 43 | 179.7 | 173.98 | 20 | 20 | 25 |
| 44 | 183.8 | 178.02 | 20 | 20 | 25 |
| 45 | 188.0 | 182.07 | 20 | 20 | 25 |
| 46 | 192.1 | 186.10 | 20 | 20 | 25 |
| 47 | 196.2 | 190.14 | 20 | 20 | 25 |
| 48 | 200.3 | 194.18 | 20 | 20 | 25 |
| 49 | 204.3 | 198.22 | 20 | 20 | 25 |
| 50 | 208.3 | 202.26 | 20 | 20 | 25 |
| 51 | 212.1 | 206.30 | 20 | 25 | 25 |
| 52 | 216.1 | 210.34 | 20 | 25 | 25 |
| 53 | 220.2 | 214.37 | 20 | 25 | 25 |
| 54 | 224.1 | 218.43 | 20 | 25 | 25 |
| 55 | 228.1 | 222.46 | 20 | 25 | 25 |
| 56 | 232.2 | 226.50 | 20 | 25 | 25 |
| 57 | 236.4 | 230.54 | 20 | 25 | 25 |
| 58 | 240.5 | 234.58 | 20 | 25 | 25 |
| 59 | 244.5 | 238.62 | 20 | 25 | 25 |
| 60 | 248.6 | 242.66 | 20 | 25 | 25 |
| 62 | 256.9 | 250.74 | 25 | 25 | 25 |
| 64 | 265.1 | 258.82 | 25 | 25 | 25 |
| 65 | 269.0 | 262.86 | 25 | 25 | 25 |
| 66 | 273.0 | 266.91 | 25 | 25 | 25 |
| 68 | 281.0 | 274.99 | 25 | 25 | 25 |
| 70 | 289.0 | 283.07 | 25 | 25 | 25 |
| 72 | 297.2 | 291.15 | 25 | 25 | 25 |
| 75 | 309.2 | 303.28 | 25 | 25 | 25 |
| 76 | 313.2 | 307.32 | 25 | 25 | 25 |
| 78 | 321.4 | 315.40 | 25 | 25 | 25 |
| 80 | 329.4 | 323.49 | 25 | 25 | 25 |
| 85 | 349.0 | 343.69 | 25 | 25 | 25 |
| 90 | 369.9 | 363.90 | 25 | 25 | 25 |
| 95 | 390.1 | 384.11 | 25 | 25 | 25 |
| 100 | 410.3 | 404.32 | 25 | 25 | 25 |
| 110 | 450.7 | 444.74 | 25 | 25 | 25 |
| 114 | 466.9 | 460.91 | 25 | 25 | 25 |
| 120 | 491.2 | 485.16 | 25 | 25 | 25 |
| 125 | 511.3 | 505.37 | 25 | 25 | 25 |
BASIC INFO.
|
Type: |
Simplex, Duplex, Triplex |
|
Sprocket Model: |
3/8″,1/2″,5/8″,3/4″,1″,1.25″,1.50″,1.75″,2.00″,2.25″,2.00″,2.25″,2.50″, 3″ |
|
Teeth Number: |
9-100 |
|
Standard: |
ANSI , JIS, DIN, ISO |
|
Material: |
1571, 1045, SS304 , SS316; As Per User Request. |
|
Performance Treatment: |
Carburizing, High Frequency Treatment, Hardening and Tempering, Nitriding |
|
Surface Treatment: |
Black of Oxidation, Zincing, Nickelage. |
| Characteristic | Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc |
| Design criterion | ISO DIN ANSI & Customer Drawings |
| Application | Industrial transmission equipment |
| Package | Wooden Case / Container and pallet, or made-to-order |
|
Certification: |
ISO9001 SGS |
|
Quality Inspection: |
Self-check and Final-check |
|
Sample: |
ODM&OEM, Trial Order Available and Welcome |
| Advantage | Quality first, Service first, Competitive price, Fast delivery |
| Delivery Time | 10 days for samples. 15 days for official order. |
INSTALLATION AND USING
The chain spocket, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.
NOTICE
When fitting new chainwheels it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.
It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.
During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
FOR CHAIN STHangZhouRDS
Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.
ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25
| ASME/ANSI B29.1-2011 Roller Chain Standard Sizes | ||||
| Size | Pitch | Maximum Roller Diameter | Minimum Ultimate Tensile Strength | Measuring Load |
|---|---|---|---|---|
| 25 | 0.250 in (6.35 mm) | 0.130 in (3.30 mm) | 780 lb (350 kg) | 18 lb (8.2 kg) |
| 35 | 0.375 in (9.53 mm) | 0.200 in (5.08 mm) | 1,760 lb (800 kg) | 18 lb (8.2 kg) |
| 41 | 0.500 in (12.70 mm) | 0.306 in (7.77 mm) | 1,500 lb (680 kg) | 18 lb (8.2 kg) |
| 40 | 0.500 in (12.70 mm) | 0.312 in (7.92 mm) | 3,125 lb (1,417 kg) | 31 lb (14 kg) |
| 50 | 0.625 in (15.88 mm) | 0.400 in (10.16 mm) | 4,880 lb (2,210 kg) | 49 lb (22 kg) |
| 60 | 0.750 in (19.05 mm) | 0.469 in (11.91 mm) | 7,030 lb (3,190 kg) | 70 lb (32 kg) |
| 80 | 1.000 in (25.40 mm) | 0.625 in (15.88 mm) | 12,500 lb (5,700 kg) | 125 lb (57 kg) |
| 100 | 1.250 in (31.75 mm) | 0.750 in (19.05 mm) | 19,531 lb (8,859 kg) | 195 lb (88 kg) |
| 120 | 1.500 in (38.10 mm) | 0.875 in (22.23 mm) | 28,125 lb (12,757 kg) | 281 lb (127 kg) |
| 140 | 1.750 in (44.45 mm) | 1.000 in (25.40 mm) | 38,280 lb (17,360 kg) | 383 lb (174 kg) |
| 160 | 2.000 in (50.80 mm) | 1.125 in (28.58 mm) | 50,000 lb (23,000 kg) | 500 lb (230 kg) |
| 180 | 2.250 in (57.15 mm) | 1.460 in (37.08 mm) | 63,280 lb (28,700 kg) | 633 lb (287 kg) |
| 200 | 2.500 in (63.50 mm) | 1.562 in (39.67 mm) | 78,175 lb (35,460 kg) | 781 lb (354 kg) |
| 240 | 3.000 in (76.20 mm) | 1.875 in (47.63 mm) | 112,500 lb (51,000 kg) | 1,000 lb (450 kg |
For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):
| Pitch (inches) | Pitch expressed in eighths |
ANSI standard chain number |
Width (inches) |
|---|---|---|---|
| 1⁄4 | 2⁄8 | 25 | 1⁄8 |
| 3⁄8 | 3⁄8 | 35 | 3⁄16 |
| 1⁄2 | 4⁄8 | 41 | 1⁄4 |
| 1⁄2 | 4⁄8 | 40 | 5⁄16 |
| 5⁄8 | 5⁄8 | 50 | 3⁄8 |
| 3⁄4 | 6⁄8 | 60 | 1⁄2 |
| 1 | 8⁄8 | 80 | 5⁄8 |
Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.
Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.
Roller chains made using ISO standard are sometimes called as isochains.
WHY CHOOSE US
1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System
The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.
We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.
| Standard Or Nonstandard: | Standard |
|---|---|
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Mining Machinery, Sugar Machinery |
| Hardness: | Hardened Tooth Surface |
| Manufacturing Method: | Cut Gear |
| Toothed Portion Shape: | Spur Gear |
| Material: | Alloy |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
| Customized Request |
|---|
Types of Bevel Gears
Bevel Gears are used in a number of industries. They are used in wheeled excavators, dredges, conveyor belts, mill actuators, and rail transmissions. A bevel gear’s spiral or angled bevel can make it suitable for confined spaces. It is also used in robotics and vertical supports of rolling mills. You can use bevel gears in food processing processes. For more information on bevel gears, read on.
Spiral bevel gear
Spiral bevel gears are used to transmit power between two shafts in a 90-degree orientation. They have curved or oblique teeth and can be fabricated from various metals. Bestagear is one manufacturer specializing in medium to large spiral bevel gears. They are used in the mining, metallurgical, marine, and oil fields. Spiral bevel gears are usually made from steel, aluminum, or phenolic materials.
Spiral bevel gears have many advantages. Their mesh teeth create a less abrupt force transfer. They are incredibly durable and are designed to last a long time. They are also less expensive than other right-angle gears. They also tend to last longer, because they are manufactured in pairs. The spiral bevel gear also reduces noise and vibration from its counterparts. Therefore, if you are in need of a new gear set, spiral bevel gears are the right choice.
The contact between spiral bevel gear teeth occurs along the surface of the gear tooth. The contact follows the Hertz theory of elastic contact. This principle holds for small significant dimensions of the contact area and small relative radii of curvature of the surfaces. In this case, strains and friction are negligible. A spiral bevel gear is a common example of an inverted helical gear. This gear is commonly used in mining equipment.
Spiral bevel gears also have a backlash-absorbing feature. This feature helps secure the thickness of the oil film on the gear surface. The shaft axis, mounting distance, and angle errors all affect the tooth contact on a spiral bevel gear. Adjusting backlash helps to correct these problems. The tolerances shown above are common for bevel gears. In some cases, manufacturers make slight design changes late in the production process, which minimizes the risk to OEMs.
Straight bevel gear
Straight bevel gears are among the easiest types of gears to manufacture. The earliest method used to manufacture straight bevel gears was to use a planer equipped with an indexing head. However, improvements have been made in manufacturing methods after the introduction of the Revacycle system and the Coniflex. The latest technology allows for even more precise manufacturing. Both of these manufacturing methods are used by CZPT. Here are some examples of straight bevel gear manufacturing.
A straight bevel gear is manufactured using two kinds of bevel surfaces, namely, the Gleason method and the Klingelnberg method. Among the two, the Gleason method is the most common. Unlike other types of gear, the CZPT method is not a universal standard. The Gleason system has higher quality gears, since its adoption of tooth crowning is the most effective way to make gears that tolerate even small assembly errors. It also eliminates the stress concentration in the bevelled edges of the teeth.
The gear’s composition depends on the application. When durability is required, a gear is made of cast iron. The pinion is usually three times harder than the gear, which helps balance wear. Other materials, such as carbon steel, are cheaper, but are less resistant to corrosion. Inertia is another critical factor to consider, since heavier gears are more difficult to reverse and stop. Precision requirements may include the gear pitch and diameter, as well as the pressure angle.
Involute geometry of a straight bevel gear is often computed by varying the surface’s normal to the surface. Involute geometry is computed by incorporating the surface coordinates and the theoretical tooth thickness. Using the CMM, the spherical involute surface can be used to determine tooth contact patterns. This method is useful when a roll tester tooling is unavailable, because it can predict the teeth’ contact pattern.
Hypoid bevel gear
Hypoid bevel gears are an efficient and versatile speed reduction solution. Their compact size, high efficiency, low noise and heat generation, and long life make them a popular choice in the power transmission and motion control industries. The following are some of the benefits of hypoid gearing and why you should use it. Listed below are some of the key misperceptions and false assumptions of this gear type. These assumptions may seem counterintuitive at first, but will help you understand what this gear is all about.
The basic concept of hypoid gears is that they use two non-intersecting shafts. The smaller gear shaft is offset from the larger gear shaft, allowing them to mesh without interference and support each other securely. The resulting torque transfer is improved when compared to conventional gear sets. A hypoid bevel gear is used to drive the rear axle of an automobile. It increases the flexibility of machine design and allows the axes to be freely adjusted.
In the first case, the mesh of the two bodies is obtained by fitting the hyperboloidal cutter to the desired gear. Its geometric properties, orientation, and position determine the desired gear. The latter is used if the desired gear is noise-free or is required to reduce vibrations. A hyperboloidal cutter, on the other hand, meshes with two toothed bodies. It is the most efficient option for modeling hypoid gears with noise concerns.
The main difference between hypoid and spiral bevel gears is that the hypoid bevel gear has a larger diameter than its counterparts. They are usually found in 1:1 and 2:1 applications, but some manufacturers also provide higher ratios. A hypoid gearbox can achieve speeds of three thousand rpm. This makes it the preferred choice in a variety of applications. So, if you’re looking for a gearbox with a high efficiency, this is the gear for you.
Addendum and dedendum angles
The addendum and dedendum angles of a bevel gear are used to describe the shape and depth of the teeth of the gear. Each tooth of the gear has a slightly tapered surface that changes in depth. These angles are defined by their addendum and dedendum distances. Addendum angle is the distance between the top land and the bottom surface of the teeth, while dedendum angle is the distance between the pitch surface and the bottom surface of the teeth.
The pitch angle is the angle formed by the apex point of the gear’s pitch cone with the pitch line of the gear shaft. The dedendum angle, on the other hand, is the depth of the tooth space below the pitch line. Both angles are used to measure the shape of a bevel gear. The addendum and dedendum angles are important for gear design.
The dedendum and addendum angles of a bevel gear are determined by the base contact ratio (Mc) of the two gears. The involute curve is not allowed to extend within the base diameter of the bevel gear. The base diameter is also a critical measurement for the design of a gear. It is possible to reduce the involute curve to match the involute curve, but it must be tangential to the involute curve.
The most common application of a bevel gear is the automotive differential. They are used in many types of vehicles, including cars, trucks, and even construction equipment. They are also used in the marine industry and aviation. Aside from these two common uses, there are many other uses for bevel gears. And they are still growing in popularity. But they’re a valuable part of automotive and industrial gearing systems.
Applications of bevel gears
Bevel gears are used in a variety of applications. They are made of various materials depending on their weight, load, and application. For high-load applications, ferrous metals such as grey cast iron are used. These materials have excellent wear resistance and are inexpensive. For lower-weight applications, steel or non-metals such as plastics are used. Some bevel gear materials are considered noiseless. Here are some of their most common uses.
Straight bevel gears are the easiest to manufacture. The earliest method of manufacturing them was with a planer with an indexing head. Modern manufacturing methods introduced the Revacycle and Coniflex systems. For industrial gear manufacturing, the CZPT uses the Revacycle system. However, there are many types of bevel gears. This guide will help you choose the right material for your next project. These materials can withstand high rotational speeds and are very strong.
Bevel gears are most common in automotive and industrial machinery. They connect the driveshaft to the wheels. Some even have a 45-degree bevel. These gears can be placed on a bevel surface and be tested for their transmission capabilities. They are also used in testing applications to ensure proper motion transmission. They can reduce the speed of straight shafts. Bevel gears can be used in many industries, from marine to aviation.
The simplest type of bevel gear is the miter gear, which has a 1:1 ratio. It is used to change the axis of rotation. The shafts of angular miter bevel gears can intersect at any angle, from 45 degrees to 120 degrees. The teeth on the bevel gear can be straight, spiral, or Zerol. And as with the rack and pinion gears, there are different types of bevel gears.
editor by CX 2023-05-18
Best made in China – replacement parts – pintle Chain & sprocket manufacturer : Cg125 idler sprockets roller chain in Barranquilla Colombia Cargo 2000-2004 Brazil Market Motorcycle Chain Sprocket with ce certificate top quality low price
We – EPG Group the largest Chain and agricultural gearbox factory in China with 5 distinct branches. For a lot more particulars: Mobile/whatsapp/telegram/Kakao us at: 0086-13083988828
Our main products are chain , gears, sprocket, Needle Roller bearings, Cylindrical Roller Bearings, Rod conclude Bearings, Spherical simple bearings, Monitor roller Bearings for Guideway, Roller Bearings, Merge Bearings for forklifts, H2o Pump Bearings, SNR Vehicle Bearings and all sorts of Spherical Bearings. Roller The higher exact CNC gear, this kind of as Sluggish-feeding wire-lower device, jig grinding device and electric powered discharge device, guarantees the prime high quality precision of mould processing, with the higher efficient and environmental protection acid rolling line becoming the largest raw material converting gear in the subject in china The wildly use of computerized milling machine, large-speed automatic feeding punch, substantial speed computerized rolling and assembling machine assures the large quality and efficiency of components and chain making. Chain Elements Each and every chain is linked at the finishes to kind a total circle or chain loop by a learn connecting url. Cotter plates or spring clips maintain the connecting link’s pins from functioning loose. ISO 9001 qualified maker of precision roller chains. Sorts incorporate one and numerous strand, hollow pin, facet bow, rollerless, self-lubricating, straight sidebar, double pitch, brushed, nickel plated, armor coated, 304 stainless metal, leaf, hoist and O-ring, citrus, sorting and caterpillar roller chains. EPT Device Technologies Co., Ltd is positioned in the lovely coastal town-HangZhou.We are a large organization groups engaged in exploring, manufacturing, marketing and advertising and technical companies, obtaining 3 large research and creation bases and one particular huge marketing and advertising center for transmission areas, chains, sprockets. Covering 80,000 sq. meters, now we have 816 personnel which includes 167 senior skilled experts and a global community of sales and support method.Retaining very good partnership with HangZhou University, HangZhou University, ZheJiang Agricultural University, ZheJiang University and Chinese Academy of Agricultural Sciences, we are receiving great technical assistance from business professionals.
“You give a request, We’ll give you a perfect solution”.We uphold the organization philosophy “integrity, performance, collaboration, innovation”, high quality 1st, innovative technology, precision manufacturing, integrity management, successful support, to help our buyers with the leading top quality goods and tremendous refined engineering.
EPT are make a total range of sprockets are accessible ex-stock for chain No.578, 503, 603, 604, SS-one hundred ten and so forth.Tooth profiles are ca EPT or equipment cut. EPT and elevator sprockets with/without flame hardened teeth are also made as for every drawing.
The use of first equipment manufacturer’s (OEM) portion figures or trademarks , e.g. CASE® and John Deere® are for reference functions only and for indicating solution use and compatibility. Our organization and the listed substitution elements contained herein are not sponsored, approved, or made by the OEM.
Best made in China – replacement parts – pintle Chain & sprocket manufacturer : China 24B-2 Sharp Top Roller Chain With 4-Points Every Pitch in Rostov-on-Don Russian Federation Chain Manufacturer Iron Chain Hardened Steel Chain Scraper Conveyor with ce certificate top quality low price
We – EPG Group the most significant Chain and agricultural gearbox factory in China with 5 distinct branches. For a lot more specifics: Mobile/whatsapp/telegram/Kakao us at: 0086-13083988828
EPG is a skilled manufacturer and exporter that is involved with the design, improvement and manufacturing.We’ve Fantastic attention has been paid on environmental safety and power preserving. built up our solution assortment to answer to the vastly various conditions discovered in distinct industrial environments around the world. From hefty industry to precision manufacturing, we function with end-users in practically each industry and have specialist solutions which are proven to provide a distinctive functionality benefit for your application. ISO 9001, ISO/TS 16949 and AS9100 licensed. Producer of common and personalized roller chains for use in a extensive variety of applications. Roller chains are available in solitary-pitch, double-pitch and precision versions. Satisfies or exceed ANSI requirements.
China chain maker iron chain hardened steel chain scraper conveyor
|
contact us
FAQ:
1. Are you a manufacturer or a trading company?
We are a professional company with over 15 years’ export knowledge for designing and generating motor vehicle machinery elements.
2. How can I get some samples?
If you need, we are glad to supply you samples for free, but the new clients are envisioned to shell out the courier expense, and the charge will be deducted from the payment for formal order.
three. Can you make casting in accordance to our drawing?
Yes, we can make casting in accordance to your drawing, 2d drawing, or 3D cad model. If the 3D cad model can be provided, the advancement of the tooling can be much more successful. But with no 3D, dependent on 2d drawing we can even now make the samples appropriately approved.
four. Can you make casting dependent on our samples?
Of course, we can make measurement based on your samples to make drawings for tooling producing.
five. What is your quality control gadget in home?
We have spectrometer in residence to keep an eye on the chemical residence, tensile te EPT equipment to management the mechanical property and EPT Sonic as NDT examining method to manage the casting detect beneath the area of casting.
ZheJiang EPT EPT Manufacture Company Ltd.
Department of EPT Sector Ltd.
Incorporate: RM 620, No 4TH, XIHU (WEST LAKE) DIS.G MANSION, LANE 5000 XIHU (WEST LAKE) DIS.XING RD, ZheJiang CHINA
Mobile: +86~13083988828: 21 56076732/5157156
Fax: 21 56496490 / 65717106
Mob:13671966510
World wide web: http://
The use of original tools manufacturer’s (OEM) portion figures or emblems , e.g. CASE® and John Deere® are for reference functions only and for indicating solution use and compatibility. Our organization and the outlined replacement areas contained herein are not sponsored, accredited, or made by the OEM.
Best China manufacturer & factory Heavy in Merca Somalia Duty Straight Sidebar Roller Chain With high quality best price
If you need to have any details or samples, please get in touch with us and you will have our quickly reply.
Overview
Rapid Information
- Applicable Industries:
-
Production Plant, Equipment Repair Retailers, farms
- Standard or Nonstandard:
-
Regular
- Sort:
-
Roller chain
-
Slip Clutch PTO Shaft for Compact Tractor Tillers NEW SLIPCLUTCH PTO SHAFT FOR COMPACT TRACTOR TILLERS ROTO TILLERS BUSHHOG RHINO KINGKUTTER,CARONI,MASCHIO,JOHN DEERE, MOST Models a few different kinds of PTO in procedure: a non shear, shear pin and slip clutch — the previous currently being the most pricey. Apply stop of non shear (r) and shear type (l) Non shear: this is a solid yoke to yoke set up and used with the expectation that certain products will not come across any sudden stops. I figure that the finishing mower does not need to have a shear set up as the blades will slip to a degree being belt driven and my other mower, the flail mower, is very forgiving in its design.
- Substance:
-
STAINLESS Metal
- Tensile Power:
-
Higher Tensile Power
- Spot of Origin:Zhejiang, China
- Manufacturer Identify:
-
OEM
- Shade:
-
Character
- Samples:
-
Offered
- Packaging:
-
Can be customized
Provide Capability
- Supply Capacity:
- a hundred thousand Meter/Meters per Month
Packaging & Supply
- Packaging Particulars
- We can also pack the chain as per ask for.”>10 feet or 3.05 meters each and every strand, packed in plywooden circumstance or pallet.
We can also pack the chain as per request.
- Port
- Shanghai/Ningbo port
On the internet Customization
Item Description
Fast Depth:
Normal and non-regular obtainable
With large top quality and aggressive price tag
Prompt delivery
Packing as for every customer’s demand from customers.
Thorough Product Description:
one) Chain NO:Z2814,Z2814-2,Z3315,Z3315-2,Z3618,Z3618-2,Z4020,Z4020-2,Z4824,Z4824-2,Z5628,Z5628-two
2) Any particular demands about pin, attachment, and plate can be meet.
3) Coloration obtainable: normal, yellow, blue, and so on
We are specialised in creating Agricultural Roller Chain, Flat Best Chain,Caterpillar Observe Chain,Hollow Pin Chain,Conveyor Chain for Beer Filling and Packing Line,Paver Chain,Attachment Sidebar Elevator Chain,Bucket Elevator Chain (Cement Mill Chain),Forging Scraper Chain,Loading Chain for Auto Industry,Loading Chain for Metallurgical Market,Conveyor Chain for Mine Machinery,Trencher Chain,Sugar Mill Chain,Double Flex Chain,and many others. Welcome calls and emails to inquiry!
we guarantee will offer the very best cost by the excellent high quality in china!We also acknowledge specific buy about the items. If you are intrigued in our items. You should do not wait to let us know.We are happy to give you the in depth info.We assure that our goods would be saftety and ended up in large good quality and sensible price. If you are fascinated in our merchandise, please contact us asap.We are sincerely seeking for your cooperation.
Most of our chain are exported to Europe and both standard and nonstandard chain accessible. We can make as for each your drawing or sample. Materials can be normal or as for each your unique ask for. If you pick us, you decide on reputable.
Related Items
|
208ASS Stainless Steel Double Pitch Roller Chain |
Conveyor Transmission Single row roller chain |
Roller chain with vulcanized elastomer profile |
|
Agricultural Chain |
Corrosion resistant stainless metal roller chain |
S Collection Agricultural Roller Chain for harvester or strolling tractors |
|
Agricultural Chain Attachments |
Corrosion resistant stainless steel roller chain |
S Type Agricultural Chain |
|
Agricultural Chain Sprocket Industrial Chain Sprocket |
Double Pitch Conveyor Roller Chain |
Limited PITCH STAINLESS Steel ROLLER CHAIN |
|
Agricultural Roller Chain |
Double Pitch Roller Chain |
Stainless collection Transmission Roller Chain |
|
Agricultural Roller Chains Collecting Chain |
Double Pitch Roller Chain Stainless Metal |
StainTo address these sealing and effectiveness concerns, Emerson Electricity Transmission (EPT) created numerous layout and producing suggestions. The resulting gearboxes are likely to operate cooler and leak totally free, in comparison with traditional worm equipment units.less Metal Double Pitch Roller Chain |
|
ANSI BL sequence Transmission Roller ChOur manufacturing facility has attained the certificate of China’s Farm Machinery Merchandise Top quality Authentication promulgated by the Farm Equipment Products Good quality Authentication Centre of China. ain |
Double Pitch Best Stainless Metal Roller Chain |
Stainless Steel Roller Chain |
|
Ansi Common Roller Chain |
Double-row Prime Roller Stainless Metal Chain |
Stainless Metal Roller Chain With Middle Conveyor Roller |
|
anticorrosion roller chain Titanium |
Good top quality roller chain stainless metal timing chains |
Stainless Metal Roller Chain With Facet Roller |
|
C & CA Agricultural Chain |
Large Obligation Offset Sidebar Roller Chain |
Stainless Steel Short Pitch Roller Chain Attachments |
|
C And CA Metal Agricultural Chain |
Heavy Duty Straight Sidebar Roller Chain |
Stainless Steel Quick Pitch Roller Chain With Straight Aspect Plate |
|
C Type And CA Agricultural Chain |
Roller Chain |
Stainless Metal Adhere Popsicles Roller Chain |
|
C Variety And CA Sort Steel Agricultural Chain Attachments |
Roller Chain For Oil Subject |
Common Roller Chain |
|
CA Sort Agricultural Chain Roller Chains |
roller chain sprocket |
Steel Conveyor Roller Chain |
|
Chain Couplings Roller Chain Type |
Roller Chain With Vulcanized Elastomer Profile |
X348 Industrial chain roller chain travel chain |
Product packaging
Also I would like to consider this chance to give a short introduction of our Ever-Electrical power company:
Our organization is a renowned company of agriculture gearbox,worm minimize gearbox, PTO shafts, Sprockets ,rollar chains, bevel equipment, pulleys and racks in china.
We have exported several items to our customers all in excess of the planet, we have lengthy-time encounter and strong technological innovation assistance.
Some of our client :
Italy: COMER,GB GEABOX ,SATI, CHIARAVALLI, AMA , Brevini
Germany: SILOKING ,GKN ,KTS
France: Itfran, Sedies
Brazil: AEMCO ,STU
Usa: John Deere , BLOUNT, Weasler, Agco, Omni Gear, WOODS
Canada: JAY-LOR , CANIMEX ,RingBall
……
-Ø Our Business with over twelve year’s history and a thousand personnel and 20 sales.
-Ø With above one hundred Million USD product sales in 2017
-Ø With progress equipment equipments
-Ø With huge operate capability and large good quality handle, ISO qualified.
……
you also can check out our site to know for far more specifics, if you require our products catalogue, you should speak to with us.
Company Information
